Syarat-syarat pembayaran & pengiriman:
|Nama Produk:||Casing Rotator||Diameter lubang bor:||1200-2600mm|
|Rotary torsi:||5292/3127/1766 kN.m Seketika 6174 kN.m||Rotary dengan kecepatan:||0.6 / 1.0 / 1.8 rpm|
|Tekanan Lengan Bawah:||Max. 830 kN + Berat mati 350 kN||Menarik Kekuatan Lengan:||3800 kN, Seketika 4340 kN|
|Tekanan-Menarik Stroke:||750 mm||Berat badan:||56 ton|
|Mesin Model:||Cummins QSX15-500||Daya mesin:||367/2100 kw / rpm|
|Konsumsi Bahan Bakar Engine:||213 g / kwh (Tingkat daya maksimum)||Mode kontrol:||Remote control berkabel|
|Berat pak daya hidraulik:||12 ton|
Casing Rotator KTR2605H
It has the caliber change device.
The convenient caliber change makes the equipment adapt to various requirements of caliber change.
It also has the auxiliary clampling device.
The auxiliary clampling device can better ensure the verticality of casing, and additionally compensate for the problem of low crane capacity of the equipped crane during deep excavation.
|Drilling Diameter||1200-2600 mm|
|Lower Pressure of sleeve||Max. 830kN+Dead Weight 350 kN|
|Pulling fore of sleeve||3800kN, Instantaneous 4340 kN|
|Pressure pulling stroke||750 mm|
|Parameters of Hydraulic power station|
|Engine Model||Cummins QSX15-500|
|Engine Power||367/2100 kw/rpm|
|Fuel Consumption of Engine||213 g/kwh( Max. power rate)|
|Control Mode||Wired remote control|
Use for different types construction:
(1) Foundation pile, continuous wall
Foundation piles for high-speed rail, road and bridge and house building;
Articulation pile constructions which are required to be excavated, such as subway platforms, underground architectures, continuous walls.
Water retaining wall of reservoir reinforcement.
(2)Drilling gravels, boulders and karst caves
It is allowable to conduct the foundation pile construction at mountain lands with gravel and boulder formations.
It is allowable to conduct operation and cast the foundation piles at the thick quicksand formation and necking down stratum or the filling layer.
Conduct rock-socketed drilling to the rock stratum, cast the foundation pile.
(3) Clear the underground obstructions
During the urban construction and bridge rebuilding, the obstructions such as the steel reinforced concrete pile, steel pipe pile, H steel pile, pc pile and wood pile can be cleared directly, and cast the foundation pile on the spot.
(4) Cut the rock stratum
Conduct the rock-socketed drilling to the cast-in-place piles.
Drill through-holes on the rock bed(shafts and ventilation holes).
(5) Deep excavation
Conduct the in-place casting or steel pipe pile inserting for the deep foundation improvement.
Excavate deep wells for construction use in the constructions of reservoir and tunnel.
(1) No noise, no vibration, and high safety.
(2) Without mud, clean working surface, good environmental friendliness, avoiding the possibility for mud to enter the concrete, high pile quality, enhancing the bond stress of concrete to the steel bar;
(3) During construction drilling, the characteristics of stratum and rock can be directly distinguished;
(4) The drilling speed is fast and reaches about 14m/h for the general soil layer;
(5) The drilling depth is large and reaches about 80m according to the situation of soil layer;
(6) The hole forming verticality is easy to master, which can be accurate to 1/500;
(7) No hole collapse will be caused, and the hole forming quality is high;
(8) The hole forming diameter is standard, with little filling factor. Being compared with other hole forming methods, it can save a lot of concrete usage;
(9) The hole clearing is thorough and fast. The drilling mud at the hole bottom can be clear to about 3.0cm.